Communication Cable U/UTP CAT5E CABLE
DC Resistance:<9.38 Ohm/100m
Mutual Capacitance: 5.6nF/100m
Characteristic Impedance:
1-100MHz: 100±15 Ohms
100-250MHz: 100±22 Ohms
Max Frequency: 100MHz
Capacitance Unbalance: 330pF/100m
Delay Skew: ≤45ns/100m
Performance Characteristics
Frequency |
RL (Min.) |
Insertion Loss (Max.) |
Propagation Delay(Max.) |
Delay Skew (Max.) |
NEXT (Min.) |
PSNEXT (Min.) |
ELNEXT (Min.) |
PSELNEXT (Min.) |
MHz |
dB |
Db/100m |
ns/100m |
ns/100m |
dB |
dB |
Db/100m |
Db/100m |
1 |
20.0 |
2.2 |
570.0 |
45.0 |
65.0 |
62.0 |
61.0 |
61.0 |
4 |
23.0 |
4.2 |
552.0 |
45.0 |
56.0 |
53.0 |
48.0 |
48.0 |
10 |
25.0 |
6.5 |
545.0 |
45.0 |
50.0 |
47.0 |
41.0 |
41.0 |
16 |
25.0 |
8.4 |
543.0 |
45.0 |
47.0 |
44.0 |
36.0 |
36.0 |
20 |
25.0 |
9.3 |
542.0 |
45.0 |
45.0 |
42.0 |
34.0 |
34.0 |
31.25 |
23.6 |
11.6 |
540.0 |
45.0 |
42.0 |
39.0 |
31.0 |
31.0 |
62.5 |
21.5 |
17.0 |
539.0 |
45.0 |
38.0 |
35.0 |
25.0 |
25.0 |
100 |
20.1 |
22.0 |
538.0 |
45.0 |
35.0 |
32.0 |
21.0 |
21.0 |
Jacket Physical Properties
Jacket | |||||
Aging |
Cold Bend |
||||
|
Item |
Aging Period |
100*24H*7D |
Cold Period |
-20±2℃*4H |
|
|
Before Aging |
After Aging |
Bending Radius |
8*Cable O.D. |
PVC |
Tensile Strength |
≥13.5Mpa |
≥12.5Mpa |
No Visible Cracks |
|
Elongation |
≥150% |
≥125% |
|||
LSZH |
Tensile Strength |
≥10.0Mpa |
≥8.0Mpa |
No Visible Cracks |
|
Elongation |
≥125% |
≥100% |
|||
PE |
Tensile Strength |
≥10.0Mpa |
≥8.0Mpa |
No Visible Cracks |
|
Elongation |
≥350% |
≥350% |
The single-core bare copper of 23AWG is used as conductor, polyethylene polymer material as insulator, flame retardant polymer material is used as jacket material, color is gray; the twisted-pair cable conforms to the requirements of the international standard (ISO/IEC), the electrical characteristics exceed the requirements of the international standard of Category VI (Cat.6), the cable center cross is isolated to ensure NEXT performance and reasonable construction bending radius. LSZH: Stands for “Low Smoke and Halogen Free”. Low smoke and halogen free material can meet the requirements of safety and environmental protection.
Application: Can be used for voice, integrated service data network (ISDN), ATM155Mbps and 622Mbps, 100Mbps TPDDI, Fast Ethernet and Gigabit Ethernet; than Category 5 and Ultra Category 5 has a long transmission distance, low transmission loss, abrasion-resistant, compression-resistant and other characteristics.
You need to cut the plastic in the center to match the length of the cable cover, then put it into the cable cover, and then insert the crystal head in order to press it, the specific steps are as follows:
How to connect Cat 6 Cable correctly?
Required materials: crystal head, Category 6 network cable, wire sets, crimping pliers, wire tester.
1. first of all, the network cable with pliers behind the stripping tool stripped.
2. stroke out the plastic of the center cross.
3. cut this plastic to the right length, in order to match the cable cover.
4. then run through the other wires.
5. Stroke and put together.
6. use pliers to cut to the right length.
7. cut the line into the line sleeve, the cross of the plastic is just on the top of the line sleeve.
8. put the wire and the wire sleeve into the crystal head.
9. with wire crimping pliers.
10. the other end to repeat the above operation, are done with a wire detector to measure whether through.
11, are through, it is complete.
Precautions:
1. Pay attention to the intensity of stripping the line, do not make too much effort to cut all the lines.
2. Category 6 cable and Category 5 cable wiring order are standard 568B: Orange and white - 1, orange - 2, green and white - 3, blue - 4, blue and white - 5, green - 6, brown and white - 7, brown - 8
Installation tips:
1. The wiring needs to be wrapped in tinfoil to prevent weak wire signal interference between the line and line. Usually use the wire when you do not need to use the tinfoil packaging.
2. The first wear into the crystal head sheath, and then use wire pliers to peel off the entire wire the outermost layer of protective film about 2.5 cm, the internal single core of the film does not peel off, otherwise it is easy to short-circuit. Then the core in accordance with the 568B wire order, straighten, shielding layer down, if the double shielding is removed from the aluminum foil, retaining the copper wire braided network down.
3. Crystal head sheath is recommended to install, because the shielding layer of the braided network cannot just let it off.